The M429R module is a PC/104 16-bit high performance Ethernet interface. It integrates an Ethernet NE2000 compatible controller with installed both 10BaseT (twisted pair) and 10Base2 (coaxial) interfaces. From Setup it is possible to select address and interrupt line, moreover it is possible to select the transmission media and to autodetect the connection cable. The 10Base2 interface is available through an additional module installed on board. If only 10BaseT interface is selected, the 10Base2 module is disabled in order to reduce the module power consumption.
The M429R comes with drivers for a wide variety of networks ands operating systems.
The M435R module (such as M440R) is an ARCNET network interface module based on COM20020 controller and is an ideal solution for applications such as industrial control, building automation, transportation, robotics and gaming. For extended functionality, moreover, the M435R module is provided with 8 programmable Outputs and 4 standard RS-232C Full modem serial ports. Each of these serial ports can be configured to use standard addresses for COMS ports or can be software configured to be mapped at user chosen addresses. Also the IRQ’s can be SW configured, so that the ports can use different IRQ lines or share an unique line.
The M441R module is a low-cost, high-performance CAN interface board that provides access to a wide range of CAN applications for PC/104 systems. The module is based on the Intel® CAN controller 82527. The 82527 controller is a highly integrated device that performs all serial communication functions such as transmission and reception of messages, message filtering on extended message frames, transmit search and interrupt search with minimal interaction from the CPU.
The M442R module is a low-cost integrated module which offers the chance of expanding the communication possibilities of a PC/104 based system. The M442R module integrates 4 serial ports: two of them are RS-232C standard serial ports in a Full Modem configuration.
ELAN™ SC520 CPU with ethernet controller
The M543R module is based on the high performances CPU ELAN™ SC520 from AMD (486 at 32 bits) 133 MHz. The module supports 32 MB or 64 MB DRAM directly soldered on- board. Optionally is available a memory chip for the error correction (ECC) management. It integrates some peripherals commonly used in standard PC applications, as Ethernet Controller 10/100baseT, 4 serials, 1 parallel, floppy and hard disk controller, socket for Solid State Disk, keyboard. The module needs only a + 5VDC supply. It can be used as stand-alone or in a PC/104 stack.
The M585R module is a new PC/104-Plus CPU module based on the Intel® Celeron® Ultra Low Voltage 400 and 650 MHz processors. The module uses the VIA ProSavage Twister T (PN133T) chipset with integrated Savage4 2D/3D Video Accelerator and supports 4X AGP VGA/LCD interface and up to 32 MB video memory. The module also integrates the VIA enhanced audio, 2 serials, 2 USB ports, 1 parallel, up to 512 MB SDRAM, 10/100BaseT Ethernet, EIDE interface (with the possibility to use IDE Flash Disks up to 2GB), keyboard/mouse controllers, Real Time Clock and Watch Dog Timer. It is able to communicate with other peripheral boards via ISA-Bus (PC/104) and also via PCI-Bus (PC/104-Plus).
he MFD2 series IDE Flash Disk is a storage device based on HYPERSTONE F2-16XN NAND type Flash controller. The module is fully compatible with IDE ATA standard interface, 44 pins connector. The MFD is free of firmware driver and it works like a normal Hard Disk Drive.
The Microvia-AOI system inspects for all of the following laser via defects: board shrinkage/expansion, conformal mask shifts, missing etchings, under drilling, over drilling, pad shifts, bias drilling, and relative size differences.
Intermas has been developing, manufacturing and marketing modular assembly systems for more than 30 years. Intermas offers an extensive range of more than 10,000 separate components including electronic enclosures, electronic subracks, RFI shielding, cable housings, interface housings, cassettes, CPCI, and IEEE, along with a full line of accessories and hardware.
The MTS690R is a very compact module that allows the control of a 4 wire resistive touch screen.
The touchscreen can be configured to work in a relative (i.e., similar to mouse functioning) or in absolute mode (i.e., the controller recognises the co-ordinates of the pressure on the touch screen). In relative mode, the standard PS/2 interface allows to the user to use standard mouse drivers provided with his Operating System, while absolute mode drivers are supplied with the module.